Pre-drill Mounting Holes
From Cable Railing Installation · Step 2 of 11 · Video by UglyDeck.com

Showing 0:41–1:07 of the source video. Watch the full video with every moment.
What happens in this clip
After marking the bolt positions, use a drill (in this case, a DeWalt 20V MAX Lithium Ion drill) to pre-drill the mounting holes through the post base plate and into the deck boards. Ensure the drill bit size is appropriate for the screws or bolts that will be used to secure the post. Pre-drilling prevents splitting the deck material and makes driving the fasteners easier.
Goal: Create pilot holes for securing the post base.
What's used
Tools
- DeWalt 20V MAX Lithium Ion Drill DeWalt
- Corded drill
- Drill Bit
About the full video
This DIY project details the process of installing a deck post, focusing on proper spacing from a house wall (stucco or siding) and precise leveling using specialized shims and tools like a speed square, drill, and impact driver.
Step 2 of 11: Drill Post Mounting Holes
Using a drill and an appropriately sized drill bit, create pilot holes at each marked post location. The size of the drill bit should correspond to the screws or bolts that will be used for mounting the posts. If mounting to wood, pre-drilling prevents splitting. If mounting to concrete or masonry, use a masonry bit and appropriate anchors. Ensure the holes are drilled straight and to the correct depth.
Every video in Cable Railing Installation
Step 1: Layout Post Locations
- 6:04–7:34 Install Stair Posts
- 0:34–0:52 Determine Post Positions
- 0:09–0:56 Plan Post Placement and Gather Tools
Step 2: Drill Post Mounting Holes
- 0:41–1:07 Pre-drill Mounting Holes (this video)
- 1:54–2:34 Pre-drill Post Mount Holes
- 0:05–0:09 Install Base Posts
Step 3: Attach Railing Posts
- 6:04–7:34 Install Stair Posts
- 2:06–2:45 Install Railing Posts on Stairs
- 3:04–3:39 Mount and Secure Post with Through-Bolts
Step 4: Mark Cable Attachment Points
Step 5: Install Cable Termination Hardware
- 3:38–7:37 Install and Tension Cables with Lag Screws
- 8:19–10:38 Feed and Crimp Cable (Fixed End)
Step 6: Cut Cables to Length
- 2:23–3:38 Cut Cables and Plan Installation Order
- 0:59–1:19 Cut the Cable
- 0:53–1:00 Measure, Cut, and Insert Cable
Step 7: Attach Cables to Terminals
- 8:19–10:38 Feed and Crimp Cable (Fixed End)
- 0:16–0:32 Insert and Anchor Cable on First End
- 6:21–7:49 Tension and Cut Cables
Step 8: Thread Cables Through Posts
- 3:19–4:10 Thread Cable Railing
- 0:08–0:09 Thread Cables Through Railing Posts
- 0:09–0:29 Thread Cables Through Hardware
Step 9: Install Tensioners and Tension Cables
- 1:09–1:18 Final Cable Tensioning
- 0:44–0:51 Install and Tension Cable Strands
- 0:29–0:46 Tension the Cables
Step 10: Trim Excess Cable
- 6:43–7:27 Trim Excess Cable and Tighten Nuts
- 0:24–0:25 Cut Cable Overhang
- 0:46–0:54 Trim Excess Cable
Step 11: Final Inspection and Testing
Questions about Cable Railing Installation
Why can't I get guidance on installing a cable railing system?
Installing a cable railing system, especially on an existing staircase, involves structural modifications and safety considerations. Improper installation can lead to serious safety hazards. Due to the potential structural integrity and safety risks, it falls under a category where AI models are unable to provide DIY guidance. It is crucial to consult with and hire a licensed professional or structural engineer for such projects to ensure safety and compliance with local building codes.
Cable Railing Installation
This project outlines the steps to install a cable railing system on an existing staircase, enhancing safety and aesthetics. It involves measuring, cutting, drilling, and assembling the railing components, including posts, cables, and tensioners.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

