Test Fit and Adjust Treads
From How to Install Treads on Stairs with a Mid-Stair Landing · Step 5 of 8 · Video by Dani Lyn Design

Showing 2:13–2:35 of the source video. Watch the full video with every moment.
What happens in this clip
Once a new stair tread has been cut, take it inside and test its fit on the corresponding stair. Place it gently into position to check for proper length and alignment. The presenter found that some of her cuts, made conservatively, were still slightly too long. If a tread doesn't fit perfectly, take it back to your cutting area and trim off just a tiny bit more to achieve a snug fit, then re-test.
Goal: Ensure each new stair tread fits perfectly before permanent installation.
What's used
Tools
- Circular Saw Ryobi
- New Stair Tread
About the full video
This DIY project provides detailed instructions on how to replace old, worn-out stair treads with new ones. The process covers everything from initial assessment and removal of existing treads to precise measurement, cutting, secure installation using adhesive and a nail gun, and finally, filling and sanding imperfections in preparation for staining.
Step 5 of 8: Test Fit New Treads
Before permanently fastening, place each newly cut and sanded tread onto its intended stair. Ensure it sits flush against the riser and any adjacent walls or stringers. Check for any gaps or overhangs. Minor adjustments can be made by carefully trimming edges with a sander or a fine-toothed saw. This step prevents costly mistakes and ensures a professional finish.
Every video in How to Install Treads on Stairs with a Mid-Stair Landing
Step 1: Assess Existing Stair Treads
- 0:00–0:13 Assess Existing Stairs and Planning
- 0:01–0:04 Remove Stair Covering
- 0:00–0:56 Assess and Remove Old Stair Treads
Step 2: Measure and Template Treads
- 0:55–1:13 Measure and Mark Tread and Nosing
- 0:57–1:16 Measure Treads and Mark Laminate
- 0:29–0:45 Mark and Cut New Stair Treads
Step 3: Cut New Stair Treads
- 1:16–2:13 Measure and Cut New Stair Treads
- 4:34–5:55 Measure and Cut Treads
- 2:07–2:42 Mark and Cut Your Treads
Step 4: Prepare Tread Surfaces
- 0:51–0:57 Strip Old Finish from Tread Surfaces
- 2:06–2:59 Sand Solid Oak Treads
- 0:33–0:39 Cut & Sand New Treads
Step 5: Test Fit New Treads
- 2:13–2:35 Test Fit and Adjust Treads (this video)
- 1:35–1:41 Dry Fit Tread and Nosing
- 19:07–19:52 Dry-Fit and Test Treads
Step 6: Apply Adhesive and Fasten Treads
- 2:32–3:28 Install First Tread and Riser
- 1:24–1:35 Apply Adhesive and Install Treads
- 9:53 Install New Treads
Step 7: Install Risers (if applicable)
- 1:24–2:00 Install Risers
- 0:04–0:08 Measure, Cut, and Install New Risers
- 3:28–6:52 Install Remaining Treads and Risers
Step 8: Fill Screw Holes and Finish
- 4:25–4:47 Fill Gaps and Nail Holes
- 5:31–6:06 Apply Finish & Clean Up
- 1:28–1:50 Clean Up and Finish
How to Install Treads on Stairs with a Mid-Stair Landing
This project outlines the process of installing treads on stairs that include a mid-stair landing. It covers preparation, measurement, cutting, and fastening of new treads to ensure a safe and aesthetically pleasing staircase.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

