Install Railing and Balusters
From Deck Stairs · Step 7 of 8 · Video by April Wilkerson

Showing 1:03–1:26 of the source video. Watch the full video with every moment.
What happens in this clip
Begin by installing the top rail, spanning from post to post. Pre-start screws in the ends of the railing pieces for easier one-handed installation while holding the railing. Secure the top rail, then the bottom rail. For the balusters, use a 2x4 (approximately 3.5 inches wide) as a spacer to ensure uniform spacing, adhering to most code regulations which require spacing less than 4 inches. Put the beveled end of the baluster down, flush to the bottom rail, and nail it into place. Repeat this process for all balusters. Once entire sections are in place, use a reciprocating saw or jigsaw to trim the wild ends of the balusters flush with the top rail.
What's used
Tools
- Circular Saw
- Clamps
- Drill/Driver
- Nail Gun
- Reciprocating Saw (or Jigsaw)
Materials
- 2x4 Lumber
- Balusters
- Screws/Nails
About the full video
This project details the demolition of an old, unsafe outdoor staircase and the construction of a new, structurally sound staircase using treated lumber, professional-grade stain, post-saver sleeves, and Simpson Strong-Tie connectors. The process includes calculating stair rise and run, marking and cutting stringers, installing posts, building a platform, and attaching treads, risers, and railings.
Step 7 of 8: Install Railings
Install railing posts securely to the deck ledger board or directly to the stringers using appropriate hardware and connectors. Then, attach the top and bottom rails between the posts. Finally, install balusters vertically between the top and bottom rails, ensuring they are spaced according to local building codes (typically no more than 4 inches apart).
Every video in Deck Stairs
Step 1: Prepare the Stair Location
- 13:17–15:33 Prepare Stair Base and Pour Concrete Pad
- 5:20–6:48 Prepare Base and Install Stair Stringers
Step 2: Mark Stringer Placement
Step 3: Attach Stringers to Deck
- 1:08–1:44 Attach Stringers to Deck Frame
- 3:14–3:53 Attach Stringers and Secure Lower Posts
- 9:31–10:14 Install Stringer Hangers and Stringers
Step 4: Secure Stringers to Ground
- 10:09–11:12 Securing Stringers to Landing Pad with Base Plate
- 5:03–5:51 Secure Stringers to Foundation & Top Support
- 1:26–1:43 Anchor Stringer Base to Footing
Step 5: Cut and Attach Risers (Optional)
- 6:51–7:45 Install New Risers and Treads
- 3:00–3:09 Attach Treads and Risers
- 7:22–9:28 Install Stringers and Attach Risers/Treads
Step 6: Install Treads
- 11:12–11:54 Attaching Tread Boards
- 1:50–2:00 Install Stair Treads
- 1:44–2:00 Attach Decking (Treads and Risers)
Step 7: Install Railings
- 1:03–1:26 Install Railing and Balusters (this video)
- 13:45–15:23 Install Railings and Balusters
- 12:17–14:26 Install Railing Rails and Balusters
Step 8: Final Inspection and Finishing Touches
- 0:34–0:55 Complete Trim and Final Cleanup
- 5:07–5:29 Final Review and Clean-up
- 0:28–0:29 Final Review and Completion
Questions about Deck Stairs
What tools and materials are essential for building deck stairs using pre-cut stringers?
You will need basic tools like a measuring tape, level, drill with drill bits, shovel, and rake for site preparation. Key materials include pre-cut pressure-treated pine stair stringers, gravel and concrete mix for securing the base, appropriate exterior structural lag screws, and decking boards for the treads. The specific list provided includes items like Anvil digging shovel, OX marking pencil, Empire plumb bob, Quikrete gravel, SAKRETE concrete mix, SPAX lag screws, and Composite Decking Boards.
What are the most critical safety precautions I should take when building deck stairs?
Safety is paramount for structural projects like deck stairs. Always wear appropriate personal protective equipment, including safety glasses, gloves, and sturdy footwear. Ensure all connections are secure and stable, especially where stringers attach to the deck and ground. Always follow manufacturer's instructions for materials and power tools, and verify stability at each step.
How can I ensure my deck stairs comply with local building codes?
Compliance with local building codes is crucial for safety and legality. Before starting, consult your local building department for requirements on rise, run, width, handrails, and foundation for deck stairs. These codes vary by location and are designed to prevent structural failure and ensure safe use. Hiring a licensed professional can help navigate these complex requirements.
What common mistakes should a beginner avoid when installing pre-cut stair stringers?
A common mistake is improper site preparation, leading to unstable ground support. Ensure the ground is level, well-compacted, and has adequate drainage using gravel and pavers. Another error is not securely attaching the stringers to both the deck and the ground, which can compromise the entire structure's stability. Always double-check measurements and use a plumb bob and level for accurate placement.
What is the estimated time commitment and difficulty for this deck stair project?
This project is rated as 'beginner' difficulty with an estimated time of 3 days. However, factors like your experience level, site conditions, and adherence to local codes can extend this. Breaking the project into manageable steps and having all tools and materials ready will help keep it on schedule.
Are there alternative materials or methods for securing deck stair stringers to the ground?
While the project suggests gravel, concrete mix, and pavers, alternative methods for ground support include concrete footings or pre-cast concrete piers. The chosen method depends on local frost lines, soil conditions, and building codes. Always ensure the ground connection is robust and prevents settlement or shifting over time.
Deck Stairs
This project outlines the process of building deck stairs using pre-cut stringers. It covers site preparation, attaching the stringers to the deck, securing them to the ground, and installing treads and railings. Safety is paramount throughout the process, and it's recommended to consult local building codes and consider hiring a professional for complex steps.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

