Vacuum Dust and Perform Fine Sanding
From How to Make Oak Stairs Less Slippery · Step 2 of 5 · Video by This Old House

Showing 1:05–1:18 of the source video. Watch the full video with every moment.
What happens in this clip
After stripping the main surface and scraping the corners, thoroughly vacuum all dust and debris from the tread surface, surrounding areas, and corners using a shop vacuum with a brush attachment. This prevents coarser dust from scratching the wood during finer sanding passes. Next, switch to 120-grit sandpaper on your random orbital sander and repeat the sanding process on the main tread surface. For edges, against the riser, and around balusters or spindles, you may need to switch to a detail sander (like a mouse sander), a multi-tool with a sanding attachment, or hand-sand with a sanding block wrapped in 120-grit sandpaper. The goal is to achieve a smooth, uniform surface, free of scratches and old finish remnants, preparing it for the new polyurethane coat. Since stair treads are high-traffic areas, a super-fine furniture finish is not always necessary; 120-grit provides a good balance of smoothness and adhesion for the finish.
Goal: Regularly vacuum dust and debris, then proceed with finer grit sanding to smooth the treads, including edges and around balusters.
What's used
Tools
- 120-grit Sandpaper
- Detail Sander (optional
- e.g.
- 'mouse' sander)
- Dust Mask/Respirator
- Hearing Protection
- Random Orbital Sander
- Safety Glasses
- Sanding Block
- Shop Vacuum (with brush attachment)
About the full video
This project provides step-by-step instructions on how to refinish worn-out stair treads, focusing on effective sanding techniques in tight spaces and proper polyurethane application for durability. It covers preparing the treads, removing old finishes, dealing with corners and edges, and applying multiple protective coats.
Step 2 of 5: Sand the Stair Treads
Using medium-grit sandpaper (e.g., 120-grit), sand each tread. The goal is not to remove a significant amount of wood, but to scuff the surface lightly. This will open the pores of the wood, allowing for better penetration and adhesion of paints, sealers, or adhesives. After sanding, vacuum up all the dust. You can also wipe down the treads with a tack cloth to ensure all fine dust particles are removed.
Every video in How to Make Oak Stairs Less Slippery
Step 1: Clean the Oak Stair Treads
- 0:03–0:07 Prepare and Clean Stairs
- 0:45–0:50 Scrub and Agitate the Wood Surface
- 0:35–0:44 Apply Wood Cleaner to Stairs
Step 2: Sand the Stair Treads
- 2:06–2:52 Sand Stair Treads and Risers
- 1:01–1:17 Sand Stair Treads
- 1:05–1:18 Vacuum Dust and Perform Fine Sanding (this video)
Step 3: Apply Anti-Slip Coating
- 0:46–0:59 Spray Clear Anti-Slip Coating
- 0:11–0:25 Apply First Coat of Non-Slip Spray
- 2:27–3:10 Apply Paint to Stairs
Step 4: Apply Anti-Slip Tape or Strips
- 1:12–1:19 Prepare Steps and Apply Non-Skid Strips
- 0:02–0:06 Apply Anti-Slip Strip
- 1:14–1:23 Apply Non-Skid Strips to Steps
Step 5: Install Anti-Slip Treads or Risers
- 0:18–0:37 Install Lower Stair Treads and Risers
How to Make Oak Stairs Less Slippery
This project outlines methods to reduce slipperiness on oak stairs, focusing on surface treatments and additions to improve grip.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

