Inspect and Fill Imperfections

What happens in this clip

Begin by thoroughly inspecting all surfaces of the hardwood stairs for any damage, such as holes, cracks, or gaps between wood pieces. Once identified, apply wood filler directly into these imperfections. Use your fingers or a trowel to ensure the filler is pressed firmly and completely into the gaps, creating a smooth and even surface that will be ready for sanding once dry.

Goal: Repair any damage or gaps in the hardwood stairs.

What's used

Tools

• Trowel
• Spatula

Materials

• Wood Filler

About the full video

This project guides you through the process of properly finishing hardwood stairs, covering essential steps from initial inspection and repair to sanding, staining, and applying multiple protective clear coats. It emphasizes meticulous preparation and correct application techniques for a durable and aesthetically pleasing result.

Step 9 of 11: Fill Nail Holes and Gaps

Using a putty knife, apply wood filler to any nail holes, screw holes, or small gaps in the hardwood treads and risers. Press the filler firmly into the voids. Smooth the excess filler flush with the wood surface using the putty knife. Allow the wood filler to dry completely according to the manufacturer's instructions.

Open this step in the guide

Every video in How to Get a Hardwood Look on Carpeted Stairs

1. Step 1: Remove Carpet and Padding

   • 0:04–0:34 Remove Old Carpet and Padding
   • 0:21–0:50 Remove the Carpet
   • 0:44–2:00 Remove Old Carpet

2. Step 2: Remove Staples and Nails

   • 0:31–0:55 Remove Tack Strips and Staples
   • 0:13–0:38 Remove Carpet and Prep for Installation
   • 1:19–1:49 Remove Staples and Protruding Nails

3. Step 3: Inspect and Repair Stair Structure

   • 0:09–0:14 Repair and Prepare Stair Structure
   • 1:40–2:44 Prepare Surface by Filling Holes
   • 3:59–6:57 Replace Damaged Stair Treads or Risers

4. Step 4: Clean and Sand Stair Surfaces

   • 1:05–1:18 Vacuum Dust and Perform Fine Sanding
   • 0:51–0:57 Strip Old Finish from Tread Surfaces
   • 0:37–0:41 Sand the Staircase

5. Step 5: Measure and Cut Hardwood Treads and Risers

   • 6:09–11:07 Measure and Cut Treads
   • 0:43–0:52 Measure and Cut New Treads
   • 3:40–6:00 Measure and Cut Risers

6. Step 6: Install Hardwood Risers

   • 0:35–0:46 Install the Riser Boards
   • 2:49–3:19 Install Retro Risers
   • 3:55–5:35 Cut and Install Stair Risers

7. Step 7: Install Hardwood Treads

   • 10:00–11:40 Install Hardwood Treads and Risers
   • 0:49–2:35 Install the Tread and Nosing Components
   • 2:35–4:25 Secure New Stair Treads

8. Step 8: Install Stair Nosing (if applicable)

   • 4:41–5:53 Cut and Install Nosings
   • 0:37–0:41 Install Stair Nose Trim
   • 13:39–14:45 Measure and Install Stair Nosing

9. Step 9: Fill Nail Holes and Gaps

   • 16:00–16:30 Apply Wood Filler for Finishing Touches
   • 0:55–1:21 Apply Wood Filler to Blemishes
   • 0:07–0:25 Inspect and Fill Imperfections (this video)

10. Step 10: Sand Repaired Areas and Final Surface

    • 2:44–3:20 Sand Surfaces and Control Dust
    • 1:21–1:35 Sand and Clean Stairs
    • 1:47–2:00 Fill and Sand Risers

11. Step 11: Apply Finish (Stain and Sealant)

    • 0:45–0:59 Apply Protective Topcoat
    • 11:09–11:34 Apply Protective Wood Top Coat
    • 2:01–2:44 Apply Polyurethane Sealer