Remove Old Carpet and Padding

What happens in this clip

Begin by removing the existing carpet and padding from the stairs. The carpet on the risers and treads is typically installed in individual pieces. Pull the carpet up with force, then remove the padding underneath. Expect to find many staples holding both the carpet and padding in place.

Goal: Clear the stairs of existing carpet and padding

What's used

Materials

• Old Carpet Padding
• Old Carpet

About the full video

This project details the process of renovating a staircase by removing old carpet, preparing the wooden treads and risers, and installing new luxury vinyl plank (LVP) flooring with matching nose molding. It covers tasks from demolition and surface preparation to precise cutting, painting, and final installation of the new stair components.

Step 1 of 11: Remove Carpet and Padding

Begin by using a utility knife to cut the carpet into manageable strips. For each strip, lift the carpet and padding off the stair tread and riser. Roll up the carpet and padding tightly as you remove it. This process should be done methodically from the top stair to the bottom.

Open this step in the guide

Every video in How to Get a Hardwood Look on Carpeted Stairs

1. Step 1: Remove Carpet and Padding

   • 0:04–0:34 Remove Old Carpet and Padding (this video)
   • 0:21–0:50 Remove the Carpet
   • 0:44–2:00 Remove Old Carpet

2. Step 2: Remove Staples and Nails

   • 0:31–0:55 Remove Tack Strips and Staples
   • 0:13–0:38 Remove Carpet and Prep for Installation
   • 1:19–1:49 Remove Staples and Protruding Nails

3. Step 3: Inspect and Repair Stair Structure

   • 0:09–0:14 Repair and Prepare Stair Structure
   • 1:40–2:44 Prepare Surface by Filling Holes
   • 3:59–6:57 Replace Damaged Stair Treads or Risers

4. Step 4: Clean and Sand Stair Surfaces

   • 1:05–1:18 Vacuum Dust and Perform Fine Sanding
   • 0:51–0:57 Strip Old Finish from Tread Surfaces
   • 0:37–0:41 Sand the Staircase

5. Step 5: Measure and Cut Hardwood Treads and Risers

   • 6:09–11:07 Measure and Cut Treads
   • 0:43–0:52 Measure and Cut New Treads
   • 3:40–6:00 Measure and Cut Risers

6. Step 6: Install Hardwood Risers

   • 0:35–0:46 Install the Riser Boards
   • 2:49–3:19 Install Retro Risers
   • 3:55–5:35 Cut and Install Stair Risers

7. Step 7: Install Hardwood Treads

   • 10:00–11:40 Install Hardwood Treads and Risers
   • 0:49–2:35 Install the Tread and Nosing Components
   • 2:35–4:25 Secure New Stair Treads

8. Step 8: Install Stair Nosing (if applicable)

   • 4:41–5:53 Cut and Install Nosings
   • 0:37–0:41 Install Stair Nose Trim
   • 13:39–14:45 Measure and Install Stair Nosing

9. Step 9: Fill Nail Holes and Gaps

   • 16:00–16:30 Apply Wood Filler for Finishing Touches
   • 0:55–1:21 Apply Wood Filler to Blemishes
   • 0:07–0:25 Inspect and Fill Imperfections

10. Step 10: Sand Repaired Areas and Final Surface

    • 2:44–3:20 Sand Surfaces and Control Dust
    • 1:21–1:35 Sand and Clean Stairs
    • 1:47–2:00 Fill and Sand Risers

11. Step 11: Apply Finish (Stain and Sealant)

    • 0:45–0:59 Apply Protective Topcoat
    • 11:09–11:34 Apply Protective Wood Top Coat
    • 2:01–2:44 Apply Polyurethane Sealer