Remove Tack Strips and Staples

What happens in this clip

After removing the carpet, carefully pull off all the tack strips from the risers and treads. Next, use a hammer and pliers to remove all the remaining staples embedded in the wood underlayment and along the edges of each tread. This is a tedious process, as there can be numerous staples on each stair. The video shows using both a hammer claw and pliers for this task.

Goal: Clear the stairs of all tack strips and staples, leaving a smooth surface.

What's used

Tools

• Ear Protection
• Earplugs
• Hammer
• Pliers

About the full video

This DIY project details the complete transformation of an old, carpeted staircase into a modern, visually appealing set of stairs with laminate treads and painted risers. The process involves removing old carpet, prepping the stairs, painting, modifying existing treads, installing new laminate, and reinstalling a painted railing.

Step 2 of 11: Remove Staples and Nails

After the carpet and padding are removed, inspect the stair treads and risers for any remaining staples or nails. Use a pair of pliers to grip and pull out any visible staples. For nails, a pry bar will be most effective. Ensure all fasteners are removed to create a smooth surface for the new hardwood.

Open this step in the guide

Every video in How to Get a Hardwood Look on Carpeted Stairs

1. Step 1: Remove Carpet and Padding

   • 0:04–0:34 Remove Old Carpet and Padding
   • 0:21–0:50 Remove the Carpet
   • 0:44–2:00 Remove Old Carpet

2. Step 2: Remove Staples and Nails

   • 0:31–0:55 Remove Tack Strips and Staples (this video)
   • 0:13–0:38 Remove Carpet and Prep for Installation
   • 1:19–1:49 Remove Staples and Protruding Nails

3. Step 3: Inspect and Repair Stair Structure

   • 0:09–0:14 Repair and Prepare Stair Structure
   • 1:40–2:44 Prepare Surface by Filling Holes
   • 3:59–6:57 Replace Damaged Stair Treads or Risers

4. Step 4: Clean and Sand Stair Surfaces

   • 1:05–1:18 Vacuum Dust and Perform Fine Sanding
   • 0:51–0:57 Strip Old Finish from Tread Surfaces
   • 0:37–0:41 Sand the Staircase

5. Step 5: Measure and Cut Hardwood Treads and Risers

   • 6:09–11:07 Measure and Cut Treads
   • 0:43–0:52 Measure and Cut New Treads
   • 3:40–6:00 Measure and Cut Risers

6. Step 6: Install Hardwood Risers

   • 0:35–0:46 Install the Riser Boards
   • 2:49–3:19 Install Retro Risers
   • 3:55–5:35 Cut and Install Stair Risers

7. Step 7: Install Hardwood Treads

   • 10:00–11:40 Install Hardwood Treads and Risers
   • 0:49–2:35 Install the Tread and Nosing Components
   • 2:35–4:25 Secure New Stair Treads

8. Step 8: Install Stair Nosing (if applicable)

   • 4:41–5:53 Cut and Install Nosings
   • 0:37–0:41 Install Stair Nose Trim
   • 13:39–14:45 Measure and Install Stair Nosing

9. Step 9: Fill Nail Holes and Gaps

   • 16:00–16:30 Apply Wood Filler for Finishing Touches
   • 0:55–1:21 Apply Wood Filler to Blemishes
   • 0:07–0:25 Inspect and Fill Imperfections

10. Step 10: Sand Repaired Areas and Final Surface

    • 2:44–3:20 Sand Surfaces and Control Dust
    • 1:21–1:35 Sand and Clean Stairs
    • 1:47–2:00 Fill and Sand Risers

11. Step 11: Apply Finish (Stain and Sealant)

    • 0:45–0:59 Apply Protective Topcoat
    • 11:09–11:34 Apply Protective Wood Top Coat
    • 2:01–2:44 Apply Polyurethane Sealer