Remove Old Carpet

What happens in this clip

Begin by removing the old carpet from the stairs. The presenter advises starting at the top of the staircase and working downwards for better leverage and momentum. Use pliers to get a firm grip on the carpet in a corner and pull it away from the tack strips. As you pull, the carpet should come up relatively easily. Once a section is loose, use a utility knife to cut the carpet into smaller, manageable strips for easier handling and disposal.

Goal: Completely remove the existing carpet from the stairs.

What's used

Tools

• Dust Mask (N95) 3M
• Knee Pads Kobalt
• Pliers Kobalt
• Claw hammer
• Safety Glasses
• Utility Knife
• Heavy-duty scissors
• Work Gloves Kobalt

About the full video

This DIY project provides a comprehensive guide on how to transform worn-out carpeted stairs into modern, durable stairs using a Cap-A-Tread stair renewal system. The process involves safely removing old carpet, padding, and tack strips, preparing the subfloor, precisely measuring and cutting new pre-finished treads and risers, and then installing them using construction adhesive to achieve a refreshed and updated look.

Step 1 of 11: Remove Carpet and Padding

Begin by using a utility knife to cut the carpet into manageable strips. For each strip, lift the carpet and padding off the stair tread and riser. Roll up the carpet and padding tightly as you remove it. This process should be done methodically from the top stair to the bottom.

Open this step in the guide

Every video in How to Get a Hardwood Look on Carpeted Stairs

1. Step 1: Remove Carpet and Padding

   • 0:04–0:34 Remove Old Carpet and Padding
   • 0:21–0:50 Remove the Carpet
   • 0:44–2:00 Remove Old Carpet (this video)

2. Step 2: Remove Staples and Nails

   • 0:31–0:55 Remove Tack Strips and Staples
   • 0:13–0:38 Remove Carpet and Prep for Installation
   • 1:19–1:49 Remove Staples and Protruding Nails

3. Step 3: Inspect and Repair Stair Structure

   • 0:09–0:14 Repair and Prepare Stair Structure
   • 1:40–2:44 Prepare Surface by Filling Holes
   • 3:59–6:57 Replace Damaged Stair Treads or Risers

4. Step 4: Clean and Sand Stair Surfaces

   • 1:05–1:18 Vacuum Dust and Perform Fine Sanding
   • 0:51–0:57 Strip Old Finish from Tread Surfaces
   • 0:37–0:41 Sand the Staircase

5. Step 5: Measure and Cut Hardwood Treads and Risers

   • 6:09–11:07 Measure and Cut Treads
   • 0:43–0:52 Measure and Cut New Treads
   • 3:40–6:00 Measure and Cut Risers

6. Step 6: Install Hardwood Risers

   • 0:35–0:46 Install the Riser Boards
   • 2:49–3:19 Install Retro Risers
   • 3:55–5:35 Cut and Install Stair Risers

7. Step 7: Install Hardwood Treads

   • 10:00–11:40 Install Hardwood Treads and Risers
   • 0:49–2:35 Install the Tread and Nosing Components
   • 2:35–4:25 Secure New Stair Treads

8. Step 8: Install Stair Nosing (if applicable)

   • 4:41–5:53 Cut and Install Nosings
   • 0:37–0:41 Install Stair Nose Trim
   • 13:39–14:45 Measure and Install Stair Nosing

9. Step 9: Fill Nail Holes and Gaps

   • 16:00–16:30 Apply Wood Filler for Finishing Touches
   • 0:55–1:21 Apply Wood Filler to Blemishes
   • 0:07–0:25 Inspect and Fill Imperfections

10. Step 10: Sand Repaired Areas and Final Surface

    • 2:44–3:20 Sand Surfaces and Control Dust
    • 1:21–1:35 Sand and Clean Stairs
    • 1:47–2:00 Fill and Sand Risers

11. Step 11: Apply Finish (Stain and Sealant)

    • 0:45–0:59 Apply Protective Topcoat
    • 11:09–11:34 Apply Protective Wood Top Coat
    • 2:01–2:44 Apply Polyurethane Sealer